How To Repair Rv Gutter Slope

0 Items In Cart
Full: $0.00

Browse by Category

How to Repair an RV Roof

Procedures, Supplies and Equipment to Repair an RV Roof or Prophylactic Roof.

Welcome to BestMaterials.com RV Roof Repair information and resource guide. We are constantly adding new resources for you to employ in repair of RV roofs and roofs built with EPDM rubber or metal and others. These solutions besides apply to commercial buildings, trailers, patios, and many house boat repairs. We welcome your RV ideas and solutions also. For coating your RV rubber roof with a premium vivid-white light traffic capable roof coating, we recommend RoofMate HT is a high performance Elastomeric Roof Sealant for light traffic areas available in handy 1G pails and larger. We also offer complete or partial replacement EPDM Rubber Roofs and likewise full EPDM Roof Kits.

Content

ane RV Roof Repair Recommendations
NEW: EPDM Repair Kits
ii Tools for EPDM Repair

2.one EPDM Roller
ii.2 3M Scotch Vivid Pad
2.three Razor Knife
2.4 Scraper

three EPDM Roof Repair Grooming

3.one Basic EPDM Surface Preparation
three.two Large Roof Surface Preparation
iii.iii EPDM Primer

4 General EPDM Repair

4.one How to Repair a Tear in EPDM
4.2 What practise I practice With Edge-Metal or Termination Bar and Screws?
4.3 How are New EPDM Lap Seams Handled When Replacing EPDM?
four.4 Preparing Wood Seam Areas for EPDM

v How to Fix a Leaky Roof-Vent, Skylight, AC Unit, or Hatch

v.i Caulking and Sealing
5.2 How to Seal Around Irregular Surfaces

half dozen How to Replace a Roof Vent, Skylight or Hatch

half-dozen.1 Permanent Sealing Process
6.ii Serviceable Sealing Process

7 How to Coat an RV EPDM Roof

seven.ane Repairing Old EPDM Seams Before Recoating
seven.two Basic Repair Process
7.iii RV Roof Re-Coating Options

8 EternaBond Information

viii.1 What is EternaBond Record?
8.2 What Makes EternaBond Different?
viii.three Is EternaBond Difficult to Install?
8.iv How UV Resistant is EternaBond?
8.5 Will EternaBond Products Stick Straight to Wood?
eight.6 Tin can I practice my Entire Roof with RoofSeal Tape?
viii.7 Tin can RoofSeal Tape Withstand Foot Traffic?
eight.eight Avoiding Dirt Drove Along Visible Edges of Coverstrip Tape
eight.9 EternaBond's Warranty

8 Types of RV Roofs

eight.one What is EPDM?
8.ii What is TPO?

RV Roof Repair Recommendations

For RV or trailer roofs and seam repairs, we recommend EternaBond. EternaBond'due south RoofSeal White is specially packaged for us with a White Ultra-UV resistant surface and wound in economical 50' rolls (rather than 37'). RoofSeal White can exist used over all types of roofs including EPDM. UV resistance of RoofSeal White is estimated at eighteen to 35 years (tested by EternaBond). RoofSeal is also available in Gray and Black. All finishes are uniform with RoofMate and AES roof coatings.

For aluminum trailer and home seam repairs, we recommend A-Seal ®. It is an aluminum faced version of RoofSeal.

For recoating a RV EPDM / prophylactic roof or metal trailer roof, we offer several good choices. For a light-traffic roof, we recommend Roofmate HT (high tensile). It cures harder to have lite foot traffic. EPDM Primer is recommended with whatsoever EPDM coating.

For a complete or partial replacement of the EPDM roofing materials, see EPDM Rubber Roofing Materials.

EPDM Repair Kits

We now offer complete EPDM repair kits using the best products available. No need to worry nigh your EPDM repair project! These kits are All-in-One EPDM roof repair.

EPDM 5x5 Repair Kit, White, 45 mil EPDM 5x5 Repair Kit, Black, HD 60 mil, Heavy Duty

Tools used for EPDM Repair

Each task is different, just generally you simply need to take some simple tools.

6 inch Putty Knife, Heavy Duty Polished Steel Putty Knife.

EPDM Roller

The roller is the most of import tool. It is critical to "roll-in" and flow the EternaBond adhesive.

3M Scotch Vivid Pad

Surfaces must exist immaculately make clean earlier applying whatever type of bonding amanuensis. When preparing a surface for EPDM clean your surface employ surface a 3M Scotch Bright Pad (Very Fine) for the job.

Razor Knife

A razor knife or PTFE Teflon® shears is the all-time tool to cut EPDM rubber. Information technology is important to minimize jagged and crude edges on your EPDM membrane.

Scraper

A scraper or joint pocketknife is used to remove sometime unwanted caulking. The best tool for this is a utility blade or scraper.

EPDM Roof Repair Preparation

If oil or grease are nowadays, remove them Outset. When using EternaBond tape (likewise as all other roof repair products), all traces of silicone sealants or waxes much be removed. Cutting out any silicone caulking, then remove any silicone surface wax with a commercial automotive pre-paint silicone / wax remover.

Re-caulk any voids with a NON-SILICONE caulk in the surface area under which the EternaBond tapes volition go. M1 sealant, a polyether sealant, is recommended. Select the sealant or caulk which all-time matches your roof surface cloth (and prior to applying the caulk/sealant into the voids, be sure to scrub seams with plastic abrasive scrubber).

EPDM rubber roof membrane cleaned earlier repairing or applying a primer.

Basic EPDM Surface Training

Castor clay off and out from under repair area. Clean all dirt and oxidation from the roof surface. The verbal method depends on roof material and type of contamination or oxidation. For pocket-sized repairs to EPDM use solvent and a rag and scrub the repair area. As needed, use a 3M Scotch Brilliant Extra Fine Pad, or a plastic annoying kitchen scrubber. Wipe and/or scrub until clean and y'all take a fresh surface. Eternaclean spray cleaner and a rag is also good to remove contagion.

Large Roof Surface Preparation

If you are re-roofing large areas y'all tin usually power wash so aggressively scrub surface using a stiff street broom (keep scrubbing until the roof is completely white once more). After drying employ EPDM Primer as per directions. Then EPDM adhesive and new EPDM membrane. Seams are best adhered with EternaBond DoubleStick. It's the best, and can exist applied without pre-priming.

When applying RoofSeal over large areas it is recommended to have a minimum ii inches of overlap seam(2" on each side of the repair area, using iv" record).

EPDM Primer

Utilize an EPDM Primer when surfaces to be bonded are very dirty (oxidized and cannot be cleaned well). EternaPrime prepares the surface into an adherent platform for the EternaBond tape to adhere to. Likewise use EternaPrime if the installation temperature will be below forty degrees F (except when using EternaBond WebSeal and One Stride, which tin can be practical down to zilch degrees F).

Use EPDM Primer prior to applying Elastomeric roof coatings, such every bit Roofmate HT or AES-125 over aged EPDM (just the EPDM must be cleaned and primed kickoff).

General EPDM Repair

This department contains situations you will ordinarily see while repairing or replacing EPDM rubber roofing membrane.

RV roof damage from a viscious blow dealt by an overhead tree branch.

RoofSeal White (iv"), our most popular RV roof repair product, was used to repair the impairment dealt to the same RV roof.

How to Repair a Tear in EPDM

Make clean the repair surface area. Remove any silicones. Clean surfaces as above. Use M1 sealant to any recesses and tool to a level surface. Allow caulk cure. Glue down whatsoever loose EPDM areas using M1 or EternaBond Doublestick. Add fasteners as needed to re-enforce the repair area. Let cure 24 hours. Use EternaBond RoofSeal with ii inches of overlap to either side of the repair area, roofing any reinforcement fasteners used. Also popular is WebSeal reinforced EternaBond record and EternaShield coating.

What practice I do With Border-Metal or Termination Bar and Screws?

For temporary repairs, overlap the entire surface with RoofSeal White. When replacing roof membrane, remove the screws and border metallic strip (termination bar). Replace membrane to only below the termination bar line. Nether the termination bar is butyl safe sealant, typically 1 inch or 3/iv inch wide. Replacement this sealant. When replacing screws, use a scrap of One thousand-1 sealant in the old holes. This volition both seal and assure the screws will not back out. And then, run a bead of M-one Sealant forth the summit edge of the termination bar. Replacement term bar tin be purchased from Best Materials. Link to Detail Drawings of Membrane Edge Terminations.

How are New EPDM Lap Seams Handled When Replacing EPDM?

After adhering new EPDM downwardly, make clean the new lap seam areas with EternaClean. Cutting DoubleStick seam sealant to length and use in seam. Coil seam well to fuse sealant.

To create permanent long-life very durable seams, a secondary layer of EPDM Primer to any OLD EPDM surface where encompass record volition be adhered (new EPDM just needs wipe downwardly with cleaner). Then employ the peel and stick COVER Tape and scroll well to fuse sealant.

Preparing Wood Seam Areas for EPDM

Set any screws with protruding heads so they are flush. Make clean off repair areas. Caulk any deep gaps with NP1 sealant. Utilise a layer of NP1 forth wood seam about 4" broad with a putty knife. Embed fiberglass reinforcement into NP1. Utilise more NP1 and plumage out the articulation (like taping a sail rock joint). Let NP1 cure before adding new EPDM sheet. Information technology takes 1-3 days, depending on weather. NP1 will not cure below 50F.

Alternatively, employ piece of EternaBond WebSeal. Its a peel and stick product which has reinforcing web. Set up screws, clean seams, skin/stick and roll well to fuse sealant. And then you can immediately apply new EPDM roofing or make other repairs.

How to Fix a Leaky Roof-Vent, Skylight, AC Unit, or Hatch

Scrape away all one-time caulking. Use a plastic scrub pad or sandpaper to clean the surface. Swab with solvent and a rag. Be sure ANY silicone type materials are removed.

Seal edge using strips of RoofSeal around the flange border to roof interface, or utilise M1 sealant. Also be sure and cover all screws. Overlap the vent flange to roof surface border by about 2" in each direction. Equally always, be sure to thoroughly whorl-in the EternaBond to seal information technology permanently.

Caulking and Sealing

The best material to use depends on the roof surface. For sealing aluminum to rubber / EPDM roofs we recommend M-1 sealant. This is a premium high-functioning materials designed for this awarding. The materials will work on ALL roof surfaces.

For setting a new vent/hatch/skylight to a fiberglass roof surface we suggest SB-140 butyl caulking under the flange. This sealant adheres very well, and creates a long-term waterproof seal between the base and roof, but tin can enable removal if service is needed. Its also UV resistant & paintable!

For resealing RV windows we recommend M-ane sealant or Duralink. Either has tremendous adhesion to drinking glass and the RV and will provide many many years of trouble-free sealing.

How to Seal Around Irregular Surfaces

Make clean surfaces and seal using EternaBond WebSeal. WebSeal's unique weaved textile bankroll and microsealant composition yous to use the tape not but on all flat surfaces but also perfectly seal around curbs, angles, pipes and bolts, making the record platonic for whatsoever roof-sealing application. It is particularly useful for difficult details, penetrations, areas where h2o ponds, and even imperfect surfaces. This 30-mil tape has no memory, so information technology will not "spring" back to it's original shape when information technology is molded to fit unusual shapes, yet it remains flexible (expands and contracts) in temperatures as low as negative 70 degrees Fahrenheit. WebSeal is designed to have a secondary surface coating over the top, EternaBond UV Protector. RoofSeal is one-step, merely does not form as readily around irregular surfaces.

How to Replace a Roof Vent, Skylight or Hatch

Scrape abroad caulking around screws that secure the item then remove screws.

Cutting abroad all one-time caulking at the metal vent-flange edge (avoiding cutting into the rubber roof). Use a putty knife to get under the vent and loosen. Carefully lift off the former vent to prevent tearing the safe roof.

Clean the roof area under and around the opening. Fill any screw holes with caulking.

At present y'all have a decision. Do you want a permanent seal, or 1 which could be serviced in the hereafter if needed?

Permanent Sealing Process

Remove 1 side of the non-stick bankroll and utilize EternaBond Doublestick record to the bottom side of the new vent flange. Press the tape into place, then curlicue well to seal tape to flange. (Note: If needed, you lot tin can easily "double stack" the Doublestick for sealing greater gaps). Alternatively, use Butyl Rubber Sealant SB-140 (much less expensive, nevertheless quite practiced).

Remove the remaining non-stick bankroll from Doublestick sealing tape. Carefully Position the new vent cover over the opening and printing hard into identify. The Doublestick tape provides an even, permanent, watertight seal. In lieu of this, use a heavy bead of caulk/sealant under the flange.

With the vent positioned, secure information technology with new exterior grade screws, such equally #9 Stainless Steel HWH with Sealing Washers. Tighten all screws gradually to pull the flange down evenly and seat the DoubleStick.

Finish the sealing by using strips of RoofSeal over the flange outer surface. Comprehend the screws and vent flange edge and roof surface two". As ever, be sure to thoroughly roll-in the EternaBond to seal it permanently.

Serviceable Sealing Process

For a seal which is temporary or tin exist more hands removed in the future, apply butyl sealing tape under the flange following the to a higher place procedure for DoubleStick. Form a good sized bead mid-manner around the bottom of the vent flange in the screw hole area. Place the vent. Move the vent around a chip to seat the vent-to-flange putty to the roof surface. (Note: Butyl Sealing Tape forms an air-tight, but not a long-term water tight seal).

With the vent positioned, secure it with new exterior grade screws, such equally #9 SS HWH W/NEO SEALING WASHER. Tighten all screws gradually to pull the flange down evenly and seat the tape.

Afterwards screws are installed, caulk the outer edge of flange-to-roof interface and screw tops with M1 caulk/sealant. OR, seal edge using strips of RoofSeal around the flange edge to roof interface, or apply M1 sealant. Also be certain and cover all screws. Overlap the vent flange to roof surface edge by about 2" in each direction. As always, be sure to thoroughly coil-in the EternaBond to seal it permanently.

How to Glaze an RV EPDM Roof

Earlier coating or recoating your RV EPDM roof you need to bank check and repair all water leaks in addition to cleaning the roof. The entire coating process may accept upwardly to a calendar week because cure times for multiple coats.

One-time RV roof with worn out coating.

This is the same RV roof pictured above. It has been recoated and will now reflect UV rays and foreclose water leaks and damage.

Repairing Former EPDM Seams Before Recoating

Clean repair areas. Remove all silicones or former coatings. Stick down whatsoever lifted areas using EternaBond DoubleStick sealant (no cure) or M1 Sealant (which must cure). Then utilize WebSeal, 4 inch.

Before applying a coating to EPDM roof, an EPDM primer is recommended. Utilise an EPDM primer in a thin layer. Let cure (about 30 minutes). Utilize EPDM roof coating, such as RoofMate HT (which will take calorie-free pes traffic), or AES-125 epoxy coating (which is very long lasting). Two coatings are required.

Basic Repair Process

This is the bones process for blanket or recoating an EPDM roof.

Repair

Repair water leaks using the techniques mentions in this article. Spot clean before repairing the roof.

Clean

Use a 1:3 bleach/water mixture practical with a stiff street broom or scrubber on other tough stains and mildew. Try TSP and water if the bleach does not perform. Or use EternaClean cleaner and a rag on oily and greasy areas. Afterwards power-wash the roof and allow information technology dry thoroughly.

Prime

Apply an EPDM roofing primer as per manufacturers instructions.

Application

Open up the can and remove any skin at the surface. Stir with a paint stick for four to 5 minutes, or with a power mixer. Apply the commencement coat with a iii/four" nap roller at charge per unit as specified by the manufacturer. Allow it cure as required, approximately ane to 3 days depending on the temperature. Apply a second coat in the same manner, except this time ringlet in the reverse direction.

RV Roof Re-Blanket Options

We recommend a lite gray or tan color. Typically greyness and tan colors hide clay, look ameliorate, and last longer than white coatings.

RoofMate HT (Low-cal Traffic)

RoofMate HT is a high functioning elastomeric Acrylic roof coating with both a High-Tensile and high elongation. Non-Flammable. Easy, curl-on awarding. Quick curing. Suitable for about 6 years before recoat. Prime before using.

Ultra Shield

Ultra Shield is also an elastomeric acrylic roof coating with an attractive performance and cost effective. Piece of cake to apply (roll-on). Quick cure. Non-flammable. Comes in several standard colors. Not traffic class. Suitable for well-nigh v years before recoat. Prime number before using.

AES-125 Epoxy Coating

AES-125 is a 2-function elastomeric, waterproofing class, very long-lasting coating. Non-chalking. Requires do to use. Not traffic grade. White color can yellow over fourth dimension.

EPDM Safety Coatings

Liquid safety and EPDM in a ii-part solvent base of operations. Highest toll. Lower elongation, Non oil resistant. Flammable when uncured. The most difficult to piece of work with. Not recommended for pes traffic areas.

EternaBond Information

Popular EternaBond leak repair products include RoofSeal, WebSeal and AlumiBond / A-Seal. These are the finest available, like shooting fish in a barrel to apply and provide easy yet permanent solutions for roof leak repairs and emergency repairs on all types of roofs, underlayment repairs, RV roof repairs, gutter seams, and other types of waterproofing repairs.

What is EternaBond Record?

EternaBond Leak Repair Tape is one the most ambitious adhesives available. EternaBond is manufactured from peculiarly formulated elastomeric resins (MicroSealants) bonded to woven, aluminum, or mixed polymers for maximum conformability. These materials are prefabricated to provide compatible thickness and volition expand/contract within normal ambience thermal conditions without e'er hardening or losing its adhesive qualities. EternaBond is perfect for surfaces like prophylactic, fiberglass, metal and even polyethylene and is now available in many convenient sizes.

What Makes EternaBond Unlike?

Most repair products autumn into one of three categories: a material with a glue applied to its surface (similar duct tape), a gum material that lacks adhesive aggressiveness, or a liquid that y'all pour and spread.

EternaBond repair tapes accept no glue or solvents considering EternaBond IS the mucilage/sealant. The highly aggressive agglutinative is extruded through a die, creating the tape shape needed for easy repairs. One side is laminated to a potent backing material and a release liner is applied on the other side.

Is EternaBond Difficult to Install?

Installing EternaBond is as easy as putting on a piece of record! EternaBond requires no glue, mixing, or caulking. For quick, emergency repairs EternaBond usually will not crave cleaning (although they recommend the repair to an unclean surface be checked at a later date for proper adhesion) and in many situations, EternaBond can exist installed underwater. DO NOT INSTALL OVER SILICONE.

How UV Resistant is EternaBond?

In UV testing, EternaBond was subjected to a 4000 Hr QUV Weather-O-meter Test with UV Light UVA 340 in the presence of humidity. Under these grueling atmospheric condition EternaBond lost only 2.8% of it's flexibility for each yard hours of exposure, while gaining 11.8% in tensile yield (strength) per 1000 hours of exposure. This extrapolates to an expected exposed life of 18 - 35 years. Technically speaking, any product that will terminal eighteen - 35 years exposed to the conditions is "environmentally stable".

Will EternaBond Products Stick Directly to Woods?

Yes. Be sure to "roll-in" product, like on other applications.

Can I exercise my Entire Roof with RoofSeal Tape?

Yes. EternaBond RoofSeal White is available in widths up to 36". You simply lay down overlapping strips to embrace the roof (and using the pre-cleaning and mail service roll-in processes). Full sheets of replacement EPDM is less expensive and much more durable.

Tin can RoofSeal Tape Withstand Foot Traffic?

No. The exterior white layer is non traffic grade. You should apply EPDM Coverstrip record for traffic area repairs. We suggest application of high-traffic roof walkway pads in the traffic areas.

Avoiding Dirt Drove Along Visible Edges of Coverstrip Tape

We recommend running a sparse dewdrop of M-1 sealant forth the visible tape edge (just plenty to comprehend the exposed EternaBond adhesive at the edge).

EternaBond's Warranty

EternaBond provide a ten-year limited warranty. Click here for the details: EternaBond Warranty.

Types of RV Roofs

RV Roofs tin be: EPDM, TPO, Metal, or Fiberglass. EPDM (available in black or white) and TPO are the about common types of RV roofs.

What is EPDM?

EPDM is synthesized from ethylene, propylene and Diene Monomer. EPDM is a highly flexible and stable material. EPDM creates the binder for the last product, vulcanized EPDM mixed condom, which contains carbon black, antioxidants, antioxidants, oils, and curing agents. The oils are added to act was plasticizers and low temperature flexibility. Over time, the oils can deplete and the EPDM sheet will compress. This is 1 of the primary aging factors.

EPDM is not resistant to oil or many solvents. Roof repair products must be compatible with EPDM and many are not (tar, bitumen, and high solvent content products can attack and decompose EPDM).

EternaBond's unique adhesive arrangement has solvent or petroleum products. It is 100% compatible with EPDM and all other roofing materials. For a final coating, Roofmate HT is fantabulous. Information technology has skillful vesture resistance, and is solvent free and so that it can be used directly over EPDM (EPDM Primer recommended).

What is TPO?

Thermoplastic polyolefin (TPO) roofing was introduced to the RV industry in well-nigh 1994. Information technology has a sleeky white surface. TPO sheeting claims to provide tear and puncture resistance xx to l percent higher than un-reinforced EPDM safety (depending on the material thickness - Best Materials). The material offers fantabulous UV protection, will not retain odors and is resistant to rot. It is easily melted or burned. This is the quickest method to identify it. Cleaning TPO can be washed with a membrane cleaner and a soft nylon castor or sponge.

Testify More Popular Products and Suppliers:

Popular Products and Pages:

Access Panels, Adhesives, Capitalist Rod, Brads Butyl Safe, Caulk & Sealants, Caulk Guns, Caulking Gun Accessories, Caulk Gun, Bulk, Chem Curbs, Chinking, Coil Roofing Nails, Concrete Anchors, Concrete Products, Concrete Repair, Concrete Stain & Sealer, Confined Space Rescue, Deck Coatings, Deck Hardware, Diamond Saw Blades, Drains, Drains-Balcony, Drain Downspouts / Nozzles, Roof Bleed Domes, Drains New-Roof, Drains-Retrofit / Reroof, Electrical Hot Air Welders, Electric Service Flashings, EPDM Accessories, Eternabond, Expansion Joints, Fall Protection Kits, Fasteners, Fire Stopping Vents, Flashing Tape, Foam Roofing, Gas & Safety Cans, Generators, Grouts, Hidden, Deck Fasteners, Hot Dipped Covering Nails, Hot Tar Kettles, Houseboat Roof/Deck Repair, Knowledgebase, Log Home Products, Lead Pipe Flashings, Lead Sheet, Lifelines-Retractables, Magnetic Hammers, Metal Roofing, Miami-Dade Nails, Mortars, Narrow Crown Stainless, Staples, NP1, Polyurethane Cream, Pipe Flashings, Pipe Supports, Ability Tools & Accessories, Propane Hot Air Welders, Propane Regulators, Propane Torches, PVC Roofing, Retrofit Piping Flashings, Rex Synfelt, Rigging/Lifting Hardware, Rivets, Rivets- Stainless, Roof Anchors, Roof Equipment Hatch, Roof Fume Vents, Roof Hatch, Roof Leak Repair, Roof Paints & Coatings, Roof Repair Materials, Roof Screws, Roofing Fasteners, Roofing Nails, Rooftop Electric Flashings, Rope, RV & Trailer Roof Repair, RV Roof Replacement, Safety Rail Systems, Saw Blades, Sealants, Sealing Washers, Snow Guards, Spray Polyurethane Foam, Stinger, Stainless Nails/Fasteners, Tarps, TPO Accessories, Underlayments, Vents, Roof Vents, Video Movies, Waterproofing Products, Window Flashing Record, Wood Deck Hardware, Zinc Sail

Pop Suppliers Include:

ACRO, Active Ventilation, AES Epoxies, AES Raptor, AJC, Albion, Alcoa/Marson, All Line, Alpha ProTech, American Sealants, Applied Technologies, ASI Products, Attic Breeze, Aztec Washer, Babcock- Davis, BAK Welders, BASF, Berger, Drupe Plastics, Biltrite, Brentwood, Brewer, CEP, Chem Link, Cleasby, CME Manufacturing, CPR, Deks, Dow, Eagle, EagleView, Erin Rope, ES Products, Eternabond, Everhard, Falltech, Flame Engineering, Flashco, Foxy, Franklin / Titebond, Fry Reglet, Greenstreak, GSSI, Guardian, Harpster, HY-C, Interwrap, ITP, ITW, Jaaco, JL Industries, Josam, Karnak, Levis, LionGuard, LSP, Lucas, Luco, Makita, Marathon, Marshalltown, Maze Nails, MEC, MFM, Miro, MM Products, National Nail, Natural Light, Newborn, OMG, Pam Fasteners, Pearl, Polar Blox, Polycoat, Portals Plus, Powers Fasteners, Prime Source, ProTech, Protecto Wrap, Pylex, Quarrix, QuickMount, RHH Foam, Robetex, Roofmaster, RoofTop Products, Senco, SFS Intec, Sievert, Simpson Stiff-Necktie, Smith, Sno Jewel, Solomon, Sonneborn, Steelhead, SunRise Solar, Dusk, Super Anchor, Surebond, Swan Secure, TRA, Trufast, United / Quest, Vulcan, Wade, Watts, Weatherbond, Werner, Western Colloid, Winco, Zurn